High Quality Stainless Steel 316 Ultrasonic Air Atomizing Nozzle Sk508 Dry Fog Nozzle
In the wave soldering process, the traditional flux spray generally uses air pressure or electromagnetic waves to make the flux atomized, and then sprayed onto the PCBA through a moving specific nozzle.
Product Details
With reliable good quality system, great standing and perfect consumer support, the series of products and solutions produced by our organization are exported to quite a few countries and regions for CBD emulsification Equipment, Benchtop Ultrasonic Spray Coating System, High Pressure Homogenizer. We adhere to the business purpose of making more profits and cultivating a loyal customer base. Based on the principle of good faith, we have established long-term cooperative relations with many customers. Now our company is further strengthening the improvement of the technical level of employees, injecting high-tech into products, and striving for better quality and more affordable products to customers at home and abroad.
Introduction of gather spray fluxing ultrasonic Spay
In the wave soldering process, the traditional flux spray generally uses air pressure or electromagnetic waves to make the flux atomized, and then sprayed onto the PCBA through a moving specific nozzle. Using the above-mentioned technology to spray flux, the atomization of the flux the particle size of the flux is not fine enough and uneven; affected by the movement of the PCBA and the nozzle, the flux sprayed on the PCBA cannot achieve uniformity. This will have a huge impact on the quality of soldering and waste a lot of flux. Used abroad the flux is atomized by an ultrasonic nozzle. The speed of atomization is determined by the speed at which the flux is introduced into the nozzle. Utilize ultrasound , A technique of wave nozzles involves the use of compressed air or nitrogen at moderate pressure to make the spray when coming out of the atomizing surface of the nozzle forming.
Difficulties of ultrasonic spraying flux
1. Low-frequency ultrasonic atomizer is better than high-frequency one. If high-frequency ultrasonic are used, small particles can be generated near the generator.Atomized particles, but due to the small nozzle diameter, when these fine atomized particles pass through the nozzle hole, they are easily fused into uneven size Of atomized particles.
2. Similarly, due to the small nozzle hole diameter, when the atomized particles pass through the nozzle hole, they will liquefy on the nozzle hole.
The impurities will remain on the nozzle hole, so that the ultrasonic nozzle is easily blocked.
3. The internal organization is particularly complex. The most solenoid valve. It can be used for two to three years (it will be completely replaced).
4. According to the different width of PCBA, adjust the distance between the two nozzles and the angle of the trachea is more complicated to operate.
5. The filter cotton in the bucket should be cleaned frequently, otherwise it will block the nozzle.
6. Spray volume.The size and speed of the flux are easily affected by the size and flow rate of the flux
7. The spray effect is easily affected by the air turbulence, resulting in the flux coating of PCBA is uneven.
We have rich experience in this area, can help you all problem about flux spray application.
Ultrasonic atomizer information | |
1.why use ultrasonic | More even£ material save£ thinner £ |
2.what’s the material | Water £ others |
3.temperature | Temperature____--____ ℃ |
4.Atomize capacity | ______L/min |
5.Particle size requirements | |
6.Spray width requirements | |
Q: Are you trading company or manufacturer?
A: We are professional manufacturer specialized in ultrasonic welding, ultrasonic cutting , ultrasonic atomizer, and ultrasonic liquid processor.
Q: How many different types of products your company manufactures?
A: Now we have more than 100 products. We have a strong advantage of OEM, we can supply technical service , design service and customize service.
Q: When can I get the price?
A: Usually we quote within 8 hours after we get your inquiry.kindly send email to admin@rps-sonic.com if you wanna get price from us.
As a large-scale manufacturer focusing on High Quality Stainless Steel 316 Ultrasonic Air Atomizing Nozzle Sk508 Dry Fog Nozzle, we shoulder the mission of 'let every company have high-quality High Quality Stainless Steel 316 Ultrasonic Air Atomizing Nozzle Sk508 Dry Fog Nozzle'. We take the enterprise spirit of "honesty, commitment, practicality and innovation". We respect our profession and treat it with a respectful and pious mind.
Hot Tags: ultrasonic atomizer nozzle, China, suppliers, manufacturers, factory, custom, probe type sonicator, Ultrasonic Liquid Emulsification Equipment, ultrasonic extraction machine, Ultrasonic Homogenizers For Liquid Processing, emulsifying mixer, ultrasonic probe mixer
[[ProKeywords]]Send Inquiry